Subaru Forester

1997-2005 of release

Repair and car operation



Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
- Systems of cooling, heating
   Specifications
   Antifreeze - the general data
   Check of serviceability of functioning and thermostat replacement
   Removal and installation of the fan of system of cooling
   Service, removal and installation of a radiator of system of cooling
   Removal and installation of a filling tank (model with a turbo-supercharging)
   Removal, check and installation of the water pump
   System of heating and salon ventilation - the general information
   Removal and heater installation
   Removal and installation of the fan of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Як в ялити рибу?
3df4be34

Removal and heater installation

Removal

Disconnect from the engine a hose bringing cooling liquid to the heat exchanger of a heater. Also disconnect taking away hose of a heater.

Details of installation of a heater

1  — the  Heater
2  — an  Air line going from воздухоприточного of a box (evaporator K/V box)
3  —  Resistive assemblage of the fan
5  —  Vozduhopritochnyj a box
6  —  Sleeves of giving of air in back foot wells

7  — the  Sealing ring
8  — the  Collar
9  — the  Submitting hose
10  — the  Taking away hose
11  — the  Stopper
12  — the  Holder


Heater design

1  — the  heater Case
2  — the  Heat exchanger
3  — an  Air line going to central дефлекторам of the panel of devices
4  — the  Distributive air line of giving of air in foot wells
5  —  Zaslonka of giving of air to nozzles blowing windshields
6, 7  —  Zaslonki of giving of air to дефлекторам salon ventilation
8, 9  —  Zaslonki of adjustment of a temperature mode
10  —  Zaslonka of giving of air in foot wells
11-15  —  drive Details заслонка
16  — the  Lateral lever of a drive airdistributing заслонок
17  — the  Screw
18  — the  Spring
19  —  Privodnoj the electromotor
20  — a  drive Arm

21  —  Draught
22, 23  —  Draughts
24  —  Clamps
25  — the  Collar
26, 27  —  Collars
28  — a  socket Arm
29  —  Draught
30, 31  —  Levers of a drive mixing and перепускной заслонок
32  — the  Air line of giving of air in a driver's foot well
33  — the  Air line of giving of air in a foot well of the forward passenger
4-36  —  fastening Details drive a management cable заслонками
37  — the  Latch of a cover of the case of a heater
1*  —  For systems with the electric servo-driver and push-button the control panel
2*  —  For hand-operated systems airdistributing заслонками and the 2-lever control panel


Design воздухоприточного a box

1  — the  Sealant
2  — the  Case in gathering
3  — the  Plate
4  —  Assemblage of the fan of a heater
5  — the  Electromotor
6  —  Krylchatka
7  — the  Hose
8  — the  Fixing nut
9  — the  Washer
10  — the  Screw
11, 12  —  Zaslonki of management рециркуляцией

13-15  —  drive Details заслонок
16  — the  Protective cover
17  — the  Servo-driver заслонок
18  — a  servo-driver Arm
19, 20  —  Draughts
21  —  the Clamp
*22  —  Burn down electroconductings
*23  — the  Arm
*24  — the  Relay
*25  — the  Clip

The elements marked with an asterisk, are established on the models equipped with system of the climate control.


 PERFORMANCE ORDER

1. Merge from the heat exchanger of a heater as much as possible a cooling liquid. At once закупорьте the open ends of hoses.
2. Disconnect приводной a cable of a choice of temperature of leaving air.
3. Disconnect electroconducting from servo-drivers заслонок a heater and воздухоприточного a box.
4. Remove the panel of devices.
5. Remove assemblage of the air line going from приточного of a box to a heater.
6. Release fixture, and remove a heater. The scheme of an arrangement of fixture of a heater
    1  —  heater Assemblage.

Installation

Installation is made in an order, the return to an order of dismantle of components. Track, that hoses охладительного a path have been tense on connecting branch pipes of the heat exchanger of a heater not less than on 25 30 mm and reliably fixed by collars. Bolts of fastening of assemblage of a heater tighten with demanded effort (5.4 9.3 Nanometers).