Subaru Forester

1997-2005 of release

Repair and car operation

Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
- The power supply system and release
   Specifications
   System of release of the fulfilled gases - the general information
   Measurement of pressure of fuel
   Pressure dump in the power supply system
   Principle of action and check of serviceability of functioning of the fuel pump
   Service of the fuel filter
   Check of a condition and replacement of fuel lines and them штуцерных connections
   Service перекидного the valve
   Removal and installation of the case of a throttle
   Injectors of injection of fuel - the general information and service
   Regulator of pressure of fuel - the general data
   Cleaning and repair of a fuel tank - the general data
   Removal and installation of the gauge of measurement of weight of air (MAF)
   Check of serviceability of functioning of system of electronic injection
   Turbo-supercharging system - the general information
   Service of system of a turbo-supercharging
   Release system - the general information
+ Engine electric equipment
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Страви з коропа

Release system - the general information

It is necessary to start service of system of release only after full cooling of its components, - remember that the surface каталитического the converter while in service the car can heat up to very heats! Track reliability of fixing of the car in the lifted position.

Typical design of system of release of the fulfilled gases

Typical design of system of release of the fulfilled gases

1  — the  Top thermofilter of a joint of a reception pipe
2  — the  Bottom thermofilter of a joint of a reception pipe
3  — the  Right collar
4  — the  Left collar
5  — the  Top thermofilter of the left section of a reception pipe
6  — the  Bottom thermofilter of the left section of a reception pipe
7  — the  Reception pipe
8  — the  Bottom thermofilter of the right section of a reception pipe
9  — the  Top thermofilter of the right section of a reception pipe
10  — the  Sealing lining
11  — the  Spring
12  —  Back section of system of release
13  —  Samokontrjashchajasja a nut
14  — the  Sealing lining
15  — the  Muffler
16  —  Rubber подвес
17  — the  Collar

18  — the  Thermofilter of average section of system of release
19  — the  Central section of system of release
20  — the  Collar In
21  — the  Top section of a thermofilter back каталитического the converter
22  — the  Bottom section of a thermofilter back каталитического the converter
23  — the  Sealing lining
24  — the  Forward oxygen gauge
25  — the  Back oxygen gauge (the Californian models)
26  — the  Back oxygen gauge (except Californian models)
27  —  Forward каталитический the converter
28  — the  Bottom section of a thermofilter forward каталитического the converter
29  — the  Top section of a thermofilter forward каталитического the converter
Т1 = 13 3 Nanometers
Т2 = 18 5 Nanometers
Т3 = 30 5 Nanometers
Т4 = 35 5 Nanometers
Т5 = 48 5 Nanometers

The design Replacement of components of system of release of the fulfilled gases consists mainly in dismantle and installation of thermoprotective screens/detachments and connection of sections of assemblage. It is necessary to remember that thermofilters and rubber подвесы basic arms should be established at assemblage strictly on the former places.

Whereas while in service the car components of system of release of the fulfilled gases constantly are exposed to aggressive influences of environment and heats, assemblage components can appear “tightly become attached” to each other, therefore, before to start to отпусканию fixture, it is necessary to impregnate joints of corresponding sections with getting oil. In especially hard cases it is necessary to take advantage ножовкой, a chisel or autogenous cutting. Will charge most correctly performance of replacement of components of system to experts of car-care centre.