Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
- Engine electric equipment
Specifications
Start of the engine from the auxiliary power supply
Removal and installation of the storage battery
Check of a condition and replacement of wires of the battery
Ignition system - the general information and safety measures
Check of serviceability of functioning of system of ignition
Assemblage of coils of ignition - the general information, check of a condition and replacement
Check and adjustment of installation of a corner of an advancing of ignition
Replacement of the module of ignition
Check of serviceability of functioning of gauges CKP, CMP and detonations
Service of spark plugs
Check of a condition of high-voltage wires
Charge system - the general information and safety measures
The generator, the general information, check and service
Removal and generator installation
Start system - the general information and safety measures
Check of serviceability of functioning of a starter and start chain
Starters Nippondenso - check and service
Starters Mitsubishi - check and service
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Service of spark plugs
See also the information resulted in Section Check of a condition and replacement of spark plugs in the Head Routine maintenance.
|
|
All spark plugs established on the engine should have identical калильное number.
|
Removal
Spark plug of the first cylinder
Design of a drive of the face key applied to removal/installation of spark plugs
|
|
1. Disconnect a negative wire from the battery.
|
|
If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! |
2. Disconnect electroconducting from gauge MAF (Heads of the Power supply system and release and the Control system of the engine see).
3. Release four clamps and remove the top cover of an air cleaner (see the Head of the Power supply system and release).
4. Release a fixing collar and disconnect from the top cover of an air cleaner an inlet air line. |
| 5. Take the air filter and release four screws of fastening of the case of an air cleaner. Remove an air cleaner. |
|
| 6. Accurately disconnect ВВ a wire from a spark plug of the first cylinder, - pull only for a tip of a contact socket and in no event for a wire! |
|
7. Put on the spark plug of the first cylinder a head of a candle key collected with карданным by a drive of a face key.
|
|
For a reversing of candles it is necessary to use a special candle head with the rubber insert of type PROTO 5020-50 protecting a porcelain insulator of a candle from damage. Observance of dimensional characteristics of elements of a drive of a candle key will allow to facilitate procedure performance considerably. |
|
|
| 8. Before to turn out a candle cover with rags the lines of hydraulic path ABS laid on affinity. |
|
|
Spark plug of the second cylinder
|
|
If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! |
|
|
|
|
1. Disconnect a negative wire from the battery.
2. Remove the storage battery. |
| 3. Accurately disconnect ВВ a wire from a spark plug of the second cylinder, - pull only for a tip of a contact socket and in no event for a wire! |
|
| 4. The candle reversing is made in the manner similar described above for candle of the cylinder first. |
|
Spark plug of the third cylinder
|
|
ВВ a wire of a spark plug of the third cylinder |
Spark plug of the fourth cylinder
|
|
If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action! |
|
|
1. Disconnect a negative wire from the battery.
2. Remove the storage battery. |
3. Turn out bolts of fastening of the tank these washing of glasses.
|
|
In order to avoid losses of a washing liquid do not disconnect from the tank hoses. |
|
|
| 4. Disconnect electroconducting from the pump of giving of a liquid of washing of glasses. |
|
| 5. Raise the tank of a liquid of washing of glasses and tie up its wire. |
|
| 6. Disconnect ВВ a wire from a spark plug of the fourth cylinder. |
|
| 7. On models with АТ cover with rags of a line of cooling ATF. |
| 8. The candle reversing is made in similar described above for candles of other cylinders to a manner, - get a candle key from outside placings of the pallet of the battery as it is shown on an illustration. |
|
|
Installation
Installation is made upside-down taking into account following moments:
- In order to avoid damage of a carving to niches of the heads made of soft metal наживление candles is better to make for the piece of a rubber hose put on their shaft, - in case of a warp the hose simply will start to be turned;
- Tighten candles with demanded effort (20.6 2.9 Nanometers).
|
|
