Subaru Forester

1997-2005 of release

Repair and car operation



Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
- Brake system
   Specifications
   System of antiblocking of brakes (ABS) - the general information and diagnostic checks
   Removal and installation of basic components ABS
   Check and adjustment of height of position and free wheeling of a pedal of a foot brake
   Adjustment of a rod of pusher gtts / of the VACUUM amplifier of brakes
   Check and adjustment of a drive of a lay brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Replacement brake колодок disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Replacement of boots and service of drum-type brake mechanisms of back wheels
   Removal and installation of components of assemblage of a lay brake (model with disk brake mechanisms of back wheels)
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake lines and hoses
   Removal and installation of assemblage of the vacuum amplifier of brakes
   Prorolling of brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


3df4be34

Removal and installation of assemblage of the vacuum amplifier of brakes

The servo-driver of vacuum strengthening of brakes does not require regular service, except for periodic checks of a condition of a vacuum hose. The description of procedure of check of serviceability of functioning of the amplifier is resulted in Section Check of serviceability of functioning of the vacuum amplifier of brakes.

The block of the vacuum amplifier of brakes is not subject to regenerative repair and in default should be replaced in gathering!


Removal

Check of a free wheeling of a pedal of a foot brake

1  — the  Rod of a pusher of the vacuum amplifier of brakes
2  — the  Counternut
3  — the  Pin
4  —  Ljuft of a pin
5  — the  Cutting finger
6  —  Ljuft of a pedal (1 3 mm)

 


 PERFORMANCE ORDER

1. Disconnect the vacuum hose brought to the amplifier from the inlet pipeline of the engine. Try not to damage a hose, removing it from the union on amplifier assemblage.
2. In car salon find knot of connection of a rod of a pusher of the vacuum amplifier to a pedal of a foot brake, - (in case of need take advantage of a pocket small lamp). At first disconnect a returnable spring, then take шплинт, liberate a cylindrical pin and disconnect a cutting finger of a pusher from the pedal lever.
3. Give fixing nuts and cautiously remove from assemblage of the vacuum amplifier the main brake cylinder (see Has undressed Removal and installation of the main brake cylinder) - try not to admit перегибания and twisting of hydraulic lines.
4. From outside salon at the left under the panel of devices give four nuts of fastening of assemblage of the vacuum amplifier to a partition of an impellent compartment, - in case of need take advantage of a pocket small lamp.
5. Pass in an impellent compartment and remove assemblage of the vacuum amplifier from a back partition. Pull assemblage strictly on an axis of its installation before full liberation of a rod of a pusher. Take assemblage from an impellent compartment.

Installation and adjustment

Size check выступания a rod of pusher ГТЦ of the vacuum amplifier of brakes

1  —  Size выступания a rod (L)
2  —  Assemblage of the vacuum amplifier
3  — the  Protective cover

 


 PERFORMANCE ORDER

1. Installation is made upside-down. All fixture tighten with demanded effort. Do not forget to replace шплинт a pin of fastening of a rod of a pusher to a pedal. Track reliability of fixing of a returnable spring.
2. Check up size выступания “L” a rod of pusher ГТЦ, - demanded value makes 10.00 mm.
3. Operating in an order, the return to a dismantle order, establish assemblage of the vacuum amplifier of brakes on the regular place, - operate extremely cautiously, try not to suppose applying of lateral loadings to a pusher rod. In case of need replace a protective cover of a rod.
4. In summary pump over a hydraulic path of brake system (the Section Prorolling of brake system see).