Subaru Forester

1997-2005 of release

Repair and car operation



Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
- Brake system
   Specifications
   System of antiblocking of brakes (ABS) - the general information and diagnostic checks
   Removal and installation of basic components ABS
   Check and adjustment of height of position and free wheeling of a pedal of a foot brake
   Adjustment of a rod of pusher gtts / of the VACUUM amplifier of brakes
   Check and adjustment of a drive of a lay brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Replacement brake колодок disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Replacement of boots and service of drum-type brake mechanisms of back wheels
   Removal and installation of components of assemblage of a lay brake (model with disk brake mechanisms of back wheels)
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake lines and hoses
   Removal and installation of assemblage of the vacuum amplifier of brakes
   Prorolling of brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
3df4be34


Removal and installation of supports of disk brake mechanisms

Remember that developed in the course of work of brake mechanisms the dust can contain extremely unhealthy the person asbestos.

At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator.

At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, - apply only firm cleaners or methyl spirit!

Supports of both brake mechanisms of one axis should vary simultaneously.

Remember that on firm car repair shops Toyota always it is possible to order the restored assemblages of brake supports on an exchange basis.


Design of the disk brake mechanism of a forward wheel

1  — the  Support
2  — the  prorolling Gate
3  — the  Directing finger
4  — the  Protective cover
5  — the  Sealing cuff
6  — the  Piston
7  —  Pylnik
8  — the  Lock ring

9  —  Ankernaja скоба
10  —  Spring clamps колодок
11  —  External adjusting washers
12  —  Internal adjusting washers
13  —  External колодка
14  —  Internal колодка
15  — the  Brake disk
16  — the  Board of the brake mechanism


Removal

 PERFORMANCE ORDER

1. Loosen the nuts of fastening of corresponding wheels. Поддомкратьте redock/back of the car also establish it on props. Cock a lay brake/prop up противооткатными boots wheels standing on the earth. Remove wheels.
2. Pump out from tank GTTS approximately 2/3 brake liquids, - at отжимании pistons level the liquid can start to be superseded from the tank. Get drain capacity under assemblage of the brake mechanism and process a surface of the last a special cleaner. Get drain capacity under assemblage of the corresponding brake mechanism and carefully wash out a surface of the last a special cleaner.
3. Disconnect from a support a brake hose, - at once закупорьте the open ends штуцерного connections. On corresponding brake mechanisms disconnect a cable of a drive of a lay brake.
4. Remove directing bolts of the brake mechanism.
5. Remove a support. Колодки and анкерная скоба their replacements of components (колодок or a brake disk) act in film only in case of need.


Installation

 PERFORMANCE ORDER

1. Installation is made upside-down, - do not forget to grease with silicone greasing directing fingers, their protective covers and bolts.
2. In summary pump over brake system (the Section Prorolling of brake system see).
3. Before to start vehicle operation make sure of serviceability of functioning of brake system.