Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
Specifications
Search of causes of failures of an electric equipment
Safety locks - the general information
Chain breakers - the general information
The relay - the general information and check of serviceability of functioning
System of additional safety (SRS) - the device and a functioning principle
Removal and installation of components SRS
Diagnostics of malfunctions SRS
Control system of speed (темпостат) - the device and a functioning principle
Adjustments of components темпостата
Check of serviceability of functioning of components and problem diagnostics темпостата
Removal and installation of components of a control system by speed
Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning, regenerative repair
Combination of devices - the general information, check of serviceability of functioning of components
Removal and installation of a combination of devices
The electric drive of rear-view mirrors - the general information, check of serviceability of functioning of components
Removal and installation of components of the electric drive of rear-view mirrors
The electric drive door Glass lifts - the general information, check of serviceability of functioning of components
Removal and installation of regulators Glass lifts
The uniform lock - the device and a functioning principle, diagnostics of malfunctions, check of a condition of components
Removal and installation of activators of door-locks
Switches of a steering column - the general information, check of serviceability of functioning
Removal and installation of switches of a steering column
Cleaners and washers of glasses - the general information, adjustment and check of a condition of components
Removal and installation of components of cleaners/washers of glasses
Replacement of lamps of lighting devices
The radio receiver aerial - the general information
Audiosystem - the general information
+ Schemes of electric connections - the general information
|
Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning, regenerative repair
The general information
|
|
Heating of external rear-view mirrors joins simultaneously with heating of back glass of the car. |
While translating the switch of heating back glasses/rear-view mirrors there is a short circuit on weight of the electromagnetic relay of a chain of giving of a food to corresponding heating elements. The display lamp of inclusion of heating is built usually in in the switch button, but can settle down and on an instrument guard. The heating system relay is in салонном the assembly block of safety locks/relays.
The working element of a heater of back glass represents a horizontal lattice from the current-carrying threads pasted on an internal surface has flown down.
Check
The scheme of an arrangement of plugs in a contact socket of the switch of heating back glasses/rear-view mirrors
Check of serviceability of functioning of the relay of heating back glasses/rear-view mirrors
Check up serviceability of functioning of the switch of heating for what, accurately having hooked, liberate it from the panel of devices. Disconnect from the switch electroconducting and check up correctness of distribution of conductivity between plugs of a contact socket of the switch in its both positions (see the table).
|
Switch position |
Plugs between which conductivity should take place |
| Выкл (OFF) |
1 and 4; 2 and 3 |
| Вкл (ON) |
1 and 4; 2 and 3; 6, 7 and 8 |
|
|
Plugs 1-4 and 2-3 serve for the illumination organisation in view of what conductivity between them takes place constantly. |
|
|
1. Remove the relay of a heater and check up correctness of distribution of conductivity between its plugs. Conductivity (with certain resistance) should take place between plugs 1 and 3 and should not take place between plugs 2 and 4. Further, submit between plugs 1 and 3 pressure, - between plugs 2 and 4 there should be a conductivity.
2. Include ignition and a heater of back glass. Press positive probe the voltmeter to the positive plug of a lattice of a heating element, negative probe press to the grounding plug. The device should register pressure of the battery, otherwise check up a condition of a safety lock, the switch and connecting electroconducting. If pressure in norm, however, a heater part does not work. Pass to a following stage of check. |
| 3. To measure pressure during described below checks wind positive probe the voltmeter with a metal foil which will be easy for pressing a finger directly to токопроводной threads of a lattice of a heating element. Negative probe a measuring instrument connect to the plug of grounding of a lattice. |
|
| 4. Measure pressure in the central part of each of lattice threads. The indication in 5 6 In testifies to serviceability of a condition of a thread. The zero indication speaks about breakage presence between the centre of a thread and an element positive side. Indication overestimate twice (10 12) occurs in the presence of breakage between the centre of a thread and an element negative side. Serially check up each of lattice threads. |
|
| 5. In the absence of breakages connect negative probe to weight of the chassis and repeat check, - indications should not change, infringement of quality of grounding of a lattice otherwise takes place. |
| 6. For breakage localisation press negative probe the voltmeter to the negative plug of a lattice of a heating element. Wrapped up by a foil positive probeом start to probe токопроводные lattice threads, moving from outside food givings to weight. In a point of breakage the instrument reading should fall from several volt to zero. |
|
|
Regenerative repair
|
|
|
|
1. Integrity restoration токопроводных threads is made by means of special two-componental electrowire paste of type Dupont № 4817.
2. Before to start regenerative repair of a lattice of a working element switch off a heater and allow to an element to cool down within several minutes.
3. Slightly smooth out the damaged site of a thread felt, then carefully wipe its spirit. |
| 4. Paste two strips of an adhesive tape along a site of a thread subject to restoration. Carefully get mixed up эпоксидную paste with a hardener (follow instructions applied in a set). Put the received structure on the damaged site (with a tipping over approximately in 20 mm on edges of the intact thread). |
|
| 5. Definitive polymerisation компаунда occurs in 24 hours after which protective strips of an adhesive tape can be removed from glass. |
|
|
|
