Subaru Forester

1997-2005 of release

Repair and car operation



Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of an electric equipment
   Safety locks - the general information
   Chain breakers - the general information
   The relay - the general information and check of serviceability of functioning
   System of additional safety (SRS) - the device and a functioning principle
   Removal and installation of components SRS
   Diagnostics of malfunctions SRS
   Control system of speed (темпостат) - the device and a functioning principle
   Adjustments of components темпостата
   Check of serviceability of functioning of components and problem diagnostics темпостата
   Removal and installation of components of a control system by speed
   Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning, regenerative repair
   Combination of devices - the general information, check of serviceability of functioning of components
   Removal and installation of a combination of devices
   The electric drive of rear-view mirrors - the general information, check of serviceability of functioning of components
   Removal and installation of components of the electric drive of rear-view mirrors
   The electric drive door Glass lifts - the general information, check of serviceability of functioning of components
   Removal and installation of regulators Glass lifts
   The uniform lock - the device and a functioning principle, diagnostics of malfunctions, check of a condition of components
   Removal and installation of activators of door-locks
   Switches of a steering column - the general information, check of serviceability of functioning
   Removal and installation of switches of a steering column
   Cleaners and washers of glasses - the general information, adjustment and check of a condition of components
   Removal and installation of components of cleaners/washers of glasses
   Replacement of lamps of lighting devices
   The radio receiver aerial - the general information
   Audiosystem - the general information
   + Schemes of electric connections - the general information


3df4be34

Combination of devices - the general information, check of serviceability of functioning of components

The general information

The structure of a combination of devices includes a speedometer, a tachometre, a measuring instrument of the expense of fuel and a measuring instrument of temperature of the engine.

Check of serviceability of functioning of components

Speedometer

 PERFORMANCE ORDER

1. Make sure of absence in memory of the block of self-diagnostics of the module of engine management of a code of malfunction VSS 2 (Heads of the Control system of the engine and a gear change Box see). If the corresponding code is present, make a necessary recovery work. In the absence of a code pass to a following stage of check.
2. Switch off ignition and remove a combination of devices (see Has undressed Removal and installation of a combination of devices).
3. Include ignition and check up pressure between weight and the plug № 7 contact sockets of a plait of electroconducting of a combination of devices. If the result of measurement makes more than 10 In, pass to a following stage of check, otherwise check up a condition of a plait of electroconducting and its contact connections. Make necessary regenerative repair.
4. Switch off ignition and measure resistance between weight and the plug № 8 contact sockets of a plait of electroconducting of a combination of devices. If the result of measurement makes less than 10 Ohm, check up serviceability of condition VSS 2 (see more low), otherwise replace electroconducting.


The gauge of speed (VSS 2)

 PERFORMANCE ORDER

1. Disconnect from located in the top part картера transmissions of gauge VSS 2 electroconducting.
2. Measure resistance between the plug № 1 contact socket of the gauge and the plug № 10 contact sockets of a plait of electroconducting of a combination of devices. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise check up an electroconducting condition on a chain site between the gauge and a combination of devices. Make necessary regenerative repair.
3. Measure resistance between the plug № 2 contact sockets of the gauge and the plug № 9 contact sockets of a plait of electroconducting of a combination of devices. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise check up an electroconducting condition on a chain site between the gauge and a combination of devices. Make necessary regenerative repair.
4. Measure resistance between plugs №№ 1 and 2 contact sockets VSS. If the result of measurement does not fall outside the limits a range 350 450 Ohm, pass to a following stage of check, otherwise replace the gauge.
5. Поддомкратьте the car also establish it on props. Start the engine and сымитируйте movement of the car with a speed over 20 km/h (12 miles/ch). Translate the voltmeter in a mode of measurement of an alternating current and measure pressure between №№ 1 and 2 gauges VSS 2. If the result of measurement makes more than 5 In, repair or replace a speedometer, otherwise replace the gauge of speed.


Tachometre

The information on check of a tachometre by manufacturers is not presented.

Temperature measuring instrument

The information on check of a measuring instrument of temperature by manufacturers is not presented.

Measuring instrument of the expense of fuel

 PERFORMANCE ORDER

1. If the arrow of a measuring instrument remains motionless, check up serviceability of giving on it of a food.
2. If a food moves regularly, pass to a following stage of check, otherwise estimate serviceability of a condition of a corresponding safety lock and connecting electroconducting. Make necessary regenerative repair.
3. Check up serviceability of a condition of the block of the gauge of measurement of the expense of fuel (see more low). In case of need make replacement (see the Head of the Power supply system and release).
4. Check up a condition of electroconducting of chains of giving of a food and grounding in a measuring instrument chain. Make necessary regenerative repair.


The gauge of measurement of the expense of fuel

 PERFORMANCE ORDER

1. The gauge of measurement of the expense of fuel is a part of assemblage of the fuel pump and is located in a petrol tank (see the Head of the Power supply system and release).
2. Take gauge assemblage / the fuel pump from a fuel tank (see the Head of the Power supply system and release) and measure resistance between corresponding plugs of a contact socket of the gauge in various positions поплавковой assemblages. Compare results of measurements to standard requirements. In case of need make replacement.


Position of a float, number of plugs

 

Demanded resistance, Ohm

The main
The block, plugs not
Are specified
Float below (the tank is empty) 50 52
Float in the middle of the course (the tank is half filled) 25 29
Float above (the tank is filled completely) 0.5 2.5
Add-telnyj
The block,
Plugs
№№ 1 and 2
Float below (the tank is empty) 42 44
Float in the middle of the course (the tank is half filled) 20 24
Float above (the tank is filled completely) 0.5 2.5