Subaru Forester

1997-2005 of release

Repair and car operation

Cleaners and washers of glasses - the general information, adjustment and check of a condition of components

The general information

The switch of management of functioning of cleaners/washers of forward and back glasses is a part of assemblage combined подрулевого the switch, - its operating lever is deduced to the right from a column.

The tank of giving of a washing liquid with the pump built in in it is established in the left forward corner of an impellent compartment.

The electromotor of a drive of cleaners of a windscreen is fixed on the right on a back partition of an impellent compartment.

The electromotor of a drive of a back screen wiper is located in the central part of a door of a back of the car.

The relay of a back screen wiper is in a luggage space, near to the right back loudspeaker.

Adjustment

Nozzles of washing of a windscreen

Adjustment snuffled givings of a liquid of washing of a windscreen


And = 450 mm In = 150 mm With = 400 mm

All measurements are made from the central line of glass.

Nozzles of forward washers should be adjusted so that streams of a liquid submitted through them got to corresponding areas of a windscreen.

Nozzle of washing of back glass

Adjustment of a nozzle of giving of a liquid of washing of back glass. Adjustment of a nozzle of a back washer should be made according to instructions


And = 80 mm In = 70 mm

All measurements are made from the central line of glass.

Levers of forward screen wipers

PERFORMANCE ORDER

1. Turn the ignition key in position RUN. Make sure that screen wipers are disconnected and stopped in the parking position.
2. Switch off ignition and adjust positions of levers of screen wipers so that the ends of brushes have appeared directly over upper edges of the ceramic seals in the bottom part of a windscreen.

The lever of a back screen wiper

PERFORMANCE ORDER


1. Include ignition. Make sure that the screen wiper is disconnected and stopped in parking (extreme by the right) position.
2. Switch off ignition and adjust position of the lever of a screen wiper.

Check

Models of cars considered in the present Management are equipped by system of additional safety (SRS).

Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Section System of additional safety (SRS) - the device and a functioning principle see).

Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation.

The electromotor of a drive of the pump of giving of a washing liquid

PERFORMANCE ORDER

1. Disconnect from built in in the tank of a washing liquid of the pump electroconducting.
2. Connect the battery to plugs №№ 1 (weight) and 2 (+) drive the electromotor. If the motor does not work at giving on it a food, replace assemblage.

Check of serviceability of functioning of the electromotor of a drive of the pump of giving of a washing liquid


1 — the Tank of a washing liquid 2 — the Battery 3 — the Contact socket of electroconducting of the motor

The electromotor of a drive of forward screen wipers

PERFORMANCE ORDER


1. Disconnect from drive the electromotor electroconducting.
2. Connect the battery to plugs №№ 6 (weight) and 2 (+) drive the electromotor. If the motor starts to rotate with small speed, pass to a following stage of check, otherwise (does not rotate, or rotates with high speed), replace the motor.
3. Connect the battery to plugs №№ 6 (weight) and 3 (+) drive the electromotor. If the motor starts to rotate with high speed, pass to a following stage of check, otherwise (does not rotate, or rotates with small speed) replace the motor. 4. Connect the battery to plugs №№ 6 (weight) and 2 (+) drive the electromotor. After the motor will start to rotate with small speed, disconnect a positive wire of the battery from the plug № 2 and connect it to the plug № 4. The Wire-crosspiece close among themselves plugs №№ 2 and 5, - the motor should start to rotate, then automatically to stop. The faulty motor is subject to replacement.

The switch of management of functioning of a drive of forward screen wipers/washers

Check of serviceability of functioning of the switch of management by functioning of forward screen wipers

PERFORMANCE ORDER

1. Remove the bottom section of furnish of the panel of devices.
2. Remove the bottom section of a casing of a steering column.
3. Release a clamp of fastening of a plait of electroconducting.
4. Disconnect electroconducting combined подрулевого the switch from кузовного a plait.
5. Check up correctness of distribution of conductivity between corresponding plugs of the switch in all working positions of the last.
6. In case of revealing of malfunctions replace assemblage combined подрулевого the switch (the Suspension bracket and a steering see the Head).

The electromotor of a drive of a back screen wiper

The scheme of an arrangement of plugs in контактно a socket of the electromotor of a drive of a back screen wiper


1 — the Electromotor 2 — the Contact socket Electroconductings 3 — the Battery

PERFORMANCE ORDER

1. Disconnect from drive the electromotor electroconducting.
2. Connect the battery to plugs №№ 3 (weight) and 2 (+) drive the electromotor. At serviceable operation of the electromotor pass to a following stage of check, otherwise replace the motor.
3. Disconnect batteries, - the motor should stop in the middle of the course.
4. Connect the battery to plugs №№ 1 (weight) and 3 (+) the motor, a wire-crosspiece close among themselves plugs №№ 2 and 4, - the motor should start to rotate, then automatically to stop. The faulty motor is subject to replacement.

The relay of the electromotor of a drive of a back screen wiper

Check of serviceability of functioning of the relay of the electromotor of a drive of a back screen wiper

PERFORMANCE ORDER

1. The relay is located behind an arch of the right back wheel.
2. Remove the relay and check up conductivity between its contact plugs №№ 1 and 2. If conductivity takes place (with nonzero resistance), pass to a following stage of check, otherwise replace the relay.
3. Submit pressure of the battery on plugs №№ 2 (-) and 1 (+) the relay and check up conductivity between plugs №№ 3 and 5. If conductivity takes place, pass to a following stage of check, otherwise replace the relay.
4. Check up conductivity between plugs №№ 3 and 4 relays. If conductivity takes place, hence, the relay as it should be, to a check stage, otherwise it is necessary to make replacement.

The switch of management of functioning of a drive back screen wipers/washers

Check of serviceability of functioning of the switch of management by functioning of forward screen wipers

PERFORMANCE ORDER