Subaru Forester

1997-2005 of release

Repair and car operation



Subaru Forester
+ Cars Subaru Forester
+ The maintenance instruction
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Gear change box
+ Coupling, трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   Specifications
   Check of a condition of spherical support of a forward suspension bracket
   Check of a condition of forward wheel bearings
   Removal and installation of a cross-section beam of a forward suspension bracket
   Removal and installation of a rotary fist from the wheel bearing, service ступичной assemblages
   Removal and installation of the bottom lever of a forward suspension bracket from a spherical support
   Service of racks of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Check of a condition of back wheel bearings
   Removal and installation of a cross-section beam (stretcher) of a back suspension bracket
   Removal, service and installation of racks of a back suspension bracket
   Removal and installation of back wheel bearings
   Prorolling of a hydraulic path of a steering drive
   Adjustment люфта gearings реечной transfers
   Check of the pressure head characteristic of the steering pump
   Check of effort of rotation of the steering mechanism
   Removal and installation of the steering pump
   Removal and installation of the steering mechanism
   Major repairs of the steering pump
   Major repairs of the steering mechanism
   Steering column, - the general information, safety measures
   Removal and installation of the module of a pillow of safety
   Removal and steering wheel installation
   Removal and installation of assemblage combined подрулевых switches
   Removal and installation of the lock of ignition/blocking of a steering column
   Removal and installation of a steering column
   Major repairs of a steering column
   Wheels and tyres - the general information
   Adjustment of geometry of a suspension bracket
+ Body
+ Onboard electric equipment
3df4be34


Removal and installation of a rotary fist from the wheel bearing, service ступичной assemblages

The removed bearings and epiploons are not subject to a reuse and should be replaced without fail!

Removal and dismantling

 PERFORMANCE ORDER

1. Disconnect the grounding tyre.
2. Поддомкратьте the car also establish it on props.
3. Remove a corresponding forward wheel.
4. Расчеканьте also turn on ступичную a nut.
5. Remove a bar of the stabilizer of cross-section stability (see Has undressed Removal and installation of the forward stabilizer of cross-section stability).
6. Disconnect from a rotary fist a support of the brake mechanism (the Brake system see the Head) and, without disconnecting a hydraulic hose, tie up it aside to suspension bracket elements.
7. Disconnect electroconducting from wheel gauge ABS.
8. By means of a special stripper (926470000) and оправки (927140000) remove power shaft assemblage (Coupling, трансмиссионная a line see the Head).
9. Remove a brake disk (the Brake system see the Head).
10. Liberate from a rotary fist a spherical support.
11. Take шплинт and release a nut of fastening of a spherical finger of a tip of steering draught. By means of a stripper liberate a tip from assemblage of a rotary fist.
12. Turn out bolts of fastening of a rotary fist to a suspension bracket rack, - preliminary mark чертилкой their adjusting positions.
13. Remove assemblage of a rotary fist from the car and transfer it on the assembly stand (927080000). Establish on fist assemblage a special stripper (927060000) and squeeze out a nave.
14. Take an internal epiploon and a lock ring.
15. Prop up a fist and squeeze out of it the internal bearing.
16. At a corresponding complete set remove from a nave a rotor of wheel gauge ABS (the Brake system see the Head).
17. By means of a special separator take from a nave the bearing and an epiploon.


Assemblage and installation

Design ступичной assemblages of a forward wheel

1  — the  Internal epiploon
2  — the  Lock ring
3  — the  Bearing
4  — the  Rotary fist
5  — the  External epiploon
6  — the  Rotor of wheel gauge ABS
7  — the  Wheel hairpin
8  — the  Nave
9  — the  Bolt of fastening of a rotor of the wheel gauge
10  —  Stupichnaja a nut

 


 PERFORMANCE ORDER

1. Using special оправки, запрессуйте in a fist internal both external bearings and epiploons, - do not forget to grease properly before installation components.

Before installation of an internal epiploon do not forget to plant a lock ring!

2. Establish on a nave a rotor of wheel gauge ABS.
3. Запрессуйте a nave in a rotary fist.
4. Establish a fist on the regular place.
5. The further installation is made in an order, the return to an order of dismantle of components. Track, that all fixture has been tightened with demanded effort.